Back

Company

Solutions

Products

服务

联系方式

联系方式
Aircraft Interiors Expo
Aircraft Interiors Expo
飞机内饰博览会(AIX)是世界领先的航空公司和供应链的市场。这一活动将整个行业聚集在一起,探索和采购最新的产品,寻找实用的解决方案,与合适的人合作并建立关系等。
6/6/2023 - 8/6/2023
中文

Optipack 电缆系统

LC-LC trunk harnesses

LC-LC trunk harnesses

Optipack harness systems (LC-LC) are used as pre-connectorised backbone links between cabinets in the data center. Generally, trunk harnesses will be connected to the rear side of patching modules and LC jumpers will be used as equipment cords to servers and switches. Backbones are generally deployed with singlemode fiber because only this fiber offers a future-proofed infrastructure for higher data rates. Multimode LC trunk harnesses are not recommended because LC multimode connectors do not offer an upgrade to 40G or 100G over parallel optics.

MTP-LC 转换线束

MTP-LC 转换线束

Optipack 转换线束提供从主干网中的 MTP 连接到交换机和服务器上的 LC 双工连接的转换。该线束提供了一种快速紧凑的替代方案,可直接插入设备收发器,而不是使用 LC 接线板和电线。如今许多数据中心设计中带有多模 MTP 主干网,因为这是最具灵活性并可满足未来需求的方式,
可将一类连接器适配到另一类上。
 

MTP-MTP 转换线束

MTP-MTP 转换线束

转换线束允许用户将他们现有的 MTP 主干网转换成可以匹配当前设备的 MTP 类型。由于转换线束可在链接中减少一对配套使用 MTP,
因此它是可替代转换模块的一种低损耗替代品。如今许多旧基础设施的设计是由一个 Base-12 MTP 主干网构成,但是经验告诉我们这种连接器很少用在拥有较高数据传输速率的交换机或服务器上。目前 40G (SR4) 收发器适合使用 Base—8 连接器,100G (SR10) 收发器适合使用 Base—24 连接器。
当前数据中心使用的 MTP 连接器类型很多,因此容易引起混淆,无法识别出不同的 Base-类型。HUBER+SUHNER 转换线束使用颜色编码套管,因此用户可以快速地识别出所需的连接类型。这对转换线束来说非常重要,因为每个组件的末端都使用了不同的连接器。
 

MTP-MTP 主干电缆

MTP-MTP 主干电缆

Optipack 主干光缆是高密度的多股光缆,可构成数据中心的主干网。Optipack 主干可使用不同光纤数,最多可用 144 芯,其通过将多股分支光缆合并成一根单模光缆的方法降低安装时间。这种方法能明显地缩短光缆的总直径,并能优化光缆布线信道内的空间使用。
Optipack 主干光缆可用 8、12 和 24 芯光纤子单元,因此用户可以部署 
Base-8、
Base-12 或 Base-24 基础设施来满足其对 MTP 连接的要求。

Base-8 trunk cables

Base-8 Optipack trunks allow users to build 10G links today which can easily be upgraded to 40G links tomorrow using 8 fiber MTP connectivity.

Base-12 trunk cables

Base-12 Optipack trunks allow users to build 10G links today which can easily be upgraded to 40G or 100G links tomorrow using conversion modules, harnesses or jumpers. This approach will result in a 33 % fiber wastage for 40G links because the transceiver requires only 8 of the 12 fibers in the cable.
 

Base-24 trunk cables

Base-24 Optipack trunks allow users to build 10G links today which can easily be upgraded to 40G or 100G links tomorrow by using conversion modules, conversion harnesses or jumpers.

Base-8 harness systems

• 8 fibers per assembly
• Compact divider
• Easy and fast snap fixation mounting
• Small diameter cable
• LC-XD uniboot for fast access
• Bend optimised fiber
• Available in SM, OM3 and OM4
• Fan-out lengths to match equipment

Base-12 harness systems

• 12 fibers per assembly
• Compact divider
• Easy and fast snap fixation mounting
• Small diameter cable
• LC-XD uniboot for fast access
• Bend optimised fiber
• Available in SM, OM3 and OM4
• Fan-out lengths to match equipment

Base-24 harness systems

• 24 fibers per assembly
• Compact divider
• Easy and fast snap fixation mounting
• Small diameter cable
• LC-XD uniboot for fast access
• Bend optimised fiber
• Available in SM, OM3 and OM4
• Fan-out lengths to match equipment

Base-8 harness system (MTP24 to 3xMTP8)

Base-8 conversion harnesses allow users to convert their 8 fiber backbone trunks into a single 24 fiber MTP connector for use in SR10 deployments (typically 100G). Three Base-8 connectors are combined inside the furcation housing so that a single MTP24 fiber connector can be plugged to the transceiver. The same harness can also be used to convert a Base-24 connector into 3 × Base-8 connectors if the backbone is based on Base-24 design.

Base-12 harness system (MTP24 to 2xMTP12)

Base-12 conversion harnesses allow users to convert their pre-installed 12 fiber backbone trunks into either Base-8 or Base-24 connections so that 40G or 100G data rates can be achieved. Two Base-12 connections are combined inside the housing to produce three Base-8 or one Base-24 connection at the other end of the assembly.

Base-8 harness system (2xMTP12 to 3xMTP8)

Base-8 conversion harnesses allow users to convert their 8 fiber backbone trunks into a single 24 fiber MTP connector for use in SR10 deployments (typically 100G). Three Base-8 connectors are combined inside the furcation housing so that a single MTP24 fiber connector can be plugged to the transceiver. The same harness can also be used to convert a Base-24 connector into 3 × Base-8 connectors if the backbone is based on Base-24 design.

DO YOU HAVE A QUESTION?